One drawback to the old mesh safety cover is that it lets in a lot of light and silt. Vacuuming in the spring is a large chore, especially since the DE filter was attached to a push-pull type of valve, with no option to ‘vacuum to waste’. Vacuuming to Waste essentially means that the pump pushes the water into the filter valve, which diverts it straight into the waste line, bypassing the filter sand, grids or cartridges. There are different ways to vacuum a pool to waste, depending on which type of filter valve you have – a multiport valve or a push-pull also called slide valve, or even no filter valve at all. Fill the pool before beginning, and run the hose while vacuuming. Shut off pump and switch the multiport valve to the Drain to Waste Position. Vacuum as fast as possible, the water level can drop fast. Stop vacuuming when the skimmer begins to suck air, allow the pool to refill. Move the backwash hose frequently to avoid erosion and oversaturation. Why and When Vacuuming to waste is helpful when there is a lot of debris in the pool, especially silty dirt, that clogs up the filter quickly, requiring you to stop vacuuming to backwash or clean the filter.

How do I hook up vacuum hose to skimmer? – Intex Krystal Clear Model 635 Pool Filter Pump 1500 Gph

You will need the pump, the filter which may be sand, D. You will also need a few tools as well to connect the pool hoses and to also connect the PVC plumbing unions that may be on both the pump and filter. You will need a screwdriver to tighten the hose clamps, a pair of channel locks to tighten the PVC plumbing unions and you may also need some Teflon tape to wrap around some of the plumbing fittings if they are loose or worn from the prior years use.

You will also need a bucket so you can prime the pump and start it up after you are all done connecting it. You will also need a source of electrical power for your above ground filter system as well. Once you have gathered the tools, made sure that you have electrical power to the outlet near your filter system you then will want to take the filter and the pump over to the filter area where you will be setting the filter system up.

The electrical hook-up of the Polaris Booster Pump should always be Filtration Pump Pool Filter Heater Polaris Booster Pump Note: Plumb the booster pump up-stream of all air inducing equipment. To Chlorinator Solar System Plumbing Options To 1, 2 or 3 Spa Typical Installation.

This is the part of Ask The Pool Pro where we deal with all the issues you may have with you pool filtration system. This page will deal with filter problems including leaks and vacuuming issues. Also included will be questions about skimmers, returns and cleaning equipment. The questions that have already been answered are found just below the invitation. Your question may have already been answered or you just may learn something new. Feel free to post a photograph with your question.

The more information I have to work with the better the answers might be. Your questions are important to me and all of my site readers. Also important are your thoughts and comments. My answers are not the only possible solutions to the problems. What have you done that has worked out well? Faster, more personalized, service is also available, for a low fee.

Please turn JavaScript on and reload the page.

If the homeowner vacuums like normal, they have a good chance of contaminating their filter, plugging up the circulation lines, or just clouding up their pool. What is the solution? Those that have filters with the 6 way Multi-port valve can vacuum their pool on Waste. This position by-passes the filter and sends all the unwanted debris through the waste line.

However, the suitability of a filter to a pool can have more to do with size, than with type. Always go at least one size larger than you think you need. Buy the largest filter .

Vacuuming your swimming pool is something that should be done on a weekly basis. Sometimes your swimming pool may not look dirty but there is actually lots of bacteria that you can not see growing on the walls and the floor of the swimming pool. The most important thing you have to remember when vacuuming any swimming pool is that have a good prime is the key to have great suction.

Often many pool owners do not spend enough time properly priming the vacuum hose only to experience hours and hours of problems because they just can not get the debris off of the pool floor. This happens because the swimming pool vacuum has a bad prime. There are a few things that you will need in order to vacuum your pool the correct way.

How Swimming Pools Work

Which type of filter is the best for an above ground pool? I work for a pool company and have found that a sand filter is the most common. An earth filter provides the best filtration but can be more time consuming and can cause a problem when using a bacquacil pool. There is also cartridge filters but i find those to be less efficient compared to the sand and earth. I would suggest that each type of filter has its own advantages and disadvantages; Sand: Affordable, dependable, easy to maintain, but not the highest level of filtration and cleaning backflushing wastes water and can be a mess.

Aug 27,  · How to hook up vacuum to sand filter hooking up the vacuum assembly is done at the poolside skimmer. there is a vacuum plate that goes over top of the skimmer basket, allowing you to leave the basket in place to catch any larger debris. the plate will have a fitting at the top to attach the vacuum hose. before turning the pump on, be sure to.

How To Install Pool Equipment Tips On How To Install Swimming Pool Equipment As a pool owner it can be difficult to find definitive information about how to install your pool equipment as well which materials you should use and in which order you should install the equipment. In the following pages Swimming Pool Steve talks about many of the commonly used installation materials and processes used to professionally install swimming pool equipment.

Installing your equipment incorrectly can damage the equipment, void your warranty and potentially even be dangerous so be sure to review these sections before installing your own equipment. Pipe materials – Learn from Swimming Pool Steve the difference between pipe materials for swimming pools, which to use when installing your equipment, and how to properly work with each material type.

Glue and primer – With grey, clear, blue, yellow, orange and other colors of glue how do you know which one to use for each application? By reading this section from Swimming Pool Steve on how to select the right glue for any swimming pool equipment installation, that’s how! Threaded connections – When it comes to swimming pool equipment installation you will need to deal with at least a few threaded pipe connections. This section will teach you which materials to use for making connections to your equipment, but more importantly which thread sealants you should NEVER use on pool equipment.

Common pipe fittings – Knowing all of the different kinds of plumbing fittings that you will need to install pool equipment is something that comes with experience. If you are installing your own pool equipment this page on commonly used plumbing fittings in the pool and spa industry will be extremely helpful. Valves and unions – The valves and unions that you use when installing your pool equipment will determine how easy it is to operate your system forever.

Spend some time on this page learning about the commonly used valves and unions as well as their orientation as part of your pool equipment mechanical installation. Pool Equipment Installation Reviews In this ongoing series Swimming Pool Steve looks at some existing pool equipment installations and discusses some of the common installation errors that are encountered in the pool and spa industry.

How to Open an Inground Pool in 13 Steps

Winterizing and storing your D. Once full close vent valve Remove any old lubricant and re-lubricate the strainer cover o-ring using water based or silicone based lubricant only! Document the pressure gauge reading Congratulations! You have successfully started up your D.

Caught up to hang up, summer waves, the filter and pool filters, above ground and download hayward sand filter. Start-Up kit for above ground filter is above ground pool. Check valve from the ground pool has an above ground swimming pool pump system features pool opening.

Dual sand filters Specially made filter sand Dual sand filters Specially made filter sand The filters in this system are high-rate sand filters. Sand filters consist of a large tank, made of fiberglass, concrete or metal, containing a thick bed of special-grade sand, which has a squarish shape. During filtering operation, dirty water from the pool comes in through the filter’s inlet pipe, which leads to the water distribution head inside the tank.

While gravity pulls the water down through the sand, the tiny sand particles catch any dirt and debris. At the bottom of the tank, the filtered water flows through the pick-up unit and out the outlet pipe. Over time, the collected dirt and debris in the sand slows down the water flow. Pressure gauges at the filter inlet and outlet give the pool custodian an idea of the blockage level inside.

If gauges show much greater pressure on the inlet pipe than the outlet pipe, the custodian knows there’s a lot of collected debris in the sand. This means it’s time to backwash the filter.

Setting Up Your Above Ground Pool Filter

We are having trouble with remembering how to connect everything since we didn’t get to open the pool last season. We are not using the heater or the auto chlorinator as they are both broken. We have a Pentair sand filter that we just cleaned out and replaced the sand with new. I understand the skimmer bottom connects to the front of the pump and that the pool wall is connected to the ‘pool return’, what gets connected to the pvc drain pipes?

It has two valve shut offs and do we have to go through the heater? Sincerely Confused Karin Hi Karin.

This pool system has a pool pump with extensive heat damage and an undersized sand filter. Also shown is the correct method to install a flow switch for a salt water chlorine system. The heater on this pool is not protected with a check valve in between the salt cell and the heater as well as a lack of bonding on the pump and heater.

Winterization also requires you to disconnect the hoses for the pool, pump and filter. Once the winter is over, and the outdoor temperatures begin to rise, it is time to reopen the pool for the summer. Trying to remember where each of the three hoses attach to your filter, pool and pump can quickly spell disaster if you mix up the connections.

Correctly hook up your sand filter and pump to your above-ground pool for hours of summer fun. Make sure to locate it near the skimmer and return on your pool. Ensure the ground is level beneath the pump and filer. Place the pump and filter on concrete blocks for additional stability. Pumps can be hardwired to the breaker, or plug into an outdoor receptacle. You may have a separate switch that operates the pump.

How to Vacuum an Intex Above Ground Pool

Inground Pool Closing Winterizing Locate all your winterizing supplies. This should include the cover, the water tubes, the plugs for the skimmers gizzmos and return jets and your winterizing chemicals. You will also need an air compressor or a powerful shop vac.

As the water passes through the filter, all the contaminants and debris get trapped in the filter, which you need to keep constantly keep clean. When choosing pool filters you need to buy them according to the size of your pool.

April 16, Subscribe to our weekly pool maintenance newsletter! Pool season has arrived. You could really go for a swim. But there you are, standing on your patio, staring at a dirty pool cover, wondering what kind of horrors await you underneath it. Every year, thousands of pool owners end up in emergency rooms due to poisoning from pool chemicals. Most of those injuries occurred because people were not wearing protective gear when handling pool chemicals.

How to Install a Pool Pump